How to Build an External Voltage Regulator for Dodge, Jeep, Chrysler

By | September 8, 2022

How to build a Dodge Jeep external voltage regulator 2
A few years ago, I had a 2000 Dodge Ram truck that the voltage regulator went out on.

Having worked on many older 70’s and 80’s cars and trucks at first, I thought it was no big deal just needed to swap out the external voltage regulator.

To my surprise, the voltage regulator now comes built into the onboard computer, which used is around $300-$600 dollars.

This was frustrating, to say the least, since the rest of the truck ran fine, and only the voltage was not regulated.

So remembering how the old Dodges worked with an external regulator, I began searching the forums looking to see how to wire one up and bypass the computer/PCM/ ECM.

To my surprise, there were many others with the same thought and experiences doing what I was looking for.

After reading through the forums and understanding how they are wired, I soon had my Dodge truck up and working in no time.

In this post, I will show how to build one or how I do it.

*This site contains affiliate links for which a commission earned.

Items Needed to Build an External Voltage Regulator

Below are the parts I use. A junkyard also might have these parts on the cheap, or they can be ordered online and are low-cost parts.

All the parts should be less than $30-$35 dollars on eBay or Amazon.

  • 1970s-1980s Dodge Voltage Regulator
  • UPDATE: A seller on Amazon has a Dodge adjustable regulator and pigtail. The adjustable regulator would be a good option for those having problems with high voltage output.

    The adjustment is a small potentiometer on the back of the unit that is turned with a small screwdriver to up or lower the output.

  • Dodge Voltage Regulator with Adjustable Potentiometer on Amazon
  • Voltage Regulator Amazon

  • Standard Dodge Voltage Regulator on Amazon
  • Tru-Tech VR125T Voltage Regulator

  • Voltage Regulator Pigtail
  • Standard Motor Products S573 Pigtail/Socket

  • Inline Fuse
  • It is a good idea to use an inline fuse.
    Nilight Waterproof Inline Fuse

  • 14 Gauge wire (I color code mine red, black and green for good ground.)
  • Screws to hold the regulator in place.
  • Electrical tape.
  • Wire Nuts (I solder the connections together, but some people use wire nuts.)

How to Build an External Voltage Regulator for Dodge, Jeep, Chrysler
Any Dodge external regulator from 1971-1989 is wired the same. I did find that the regulators from the 1970s put out less voltage than the 1980’s versions, but the wiring is the same.
External Voltage Regulator Kit for Dodge Chrysler Jeep
The wiring is simple enough, with only three wires needed and a good ground.

The center pole on the regulator needs two wires, one that goes to the positive side of the battery and one that goes to the alternator.

The outer side pole on the regulator also goes to the alternator.
How to Build a External Voltage Regulator for Dodge 2020
The labeled Red wire in the above picture goes to the positive side of the battery; the other two wires go to the back of the alternator.

If you look at the back of the alternator, there will be three connections, one large gauge wire going to the starter that hooks to the positive battery terminal and two small wires that go to the computer.

The two small wires are what regulate the voltage and are the only connections that need modifying on the alternator.

The two wires that go into the alternator from the voltage regulator do not matter and are interchangeable since it is alternating current.

The only wire that is very important (since it will fry the regulator if done wrong) is the center pole on the regulator that goes to the positive battery terminal.
Step by Step How To Make a External Voltage Regulator to bypass a Dodge Jeep computer ECM and save money
If the center terminal wire going to the positive side of the battery is wired wrong, the regulator will fry.

The center regulator wire will also drain the battery slowly if left connected with a vehicle while not running.
Step by Step How To Make a External Voltage Regulator to bypass a Dodge Jeep computer ECM and Save
To stop the battery from draining, it is usually wired into the fuse box on at least a 20 Amp fuse, so it breaks the connection when the vehicle is turned off.

Another option is to put in a manual on/off switch somewhere that will break the connection manually.

Either way, simply remember if it is left hooked to the positive terminal, it will slowly drain the battery.

Another important step is that the external regulator must have a good ground to the alternator. If there is no good ground, then the voltage will swing wildly.
Step by Step How To Make a External Voltage Regulator to bypass a Dodge Jeep computer ECM Good Ground
A simple way to be sure it is grounded well is to run a ground wire from the alternator casing to the external voltage regulator casing.

Bob Thomas
Latest posts by Bob Thomas (see all)

51 thoughts on “How to Build an External Voltage Regulator for Dodge, Jeep, Chrysler

  1. Kael

    This works on ’06 alternators for the Dodge Ram! They changed it in ’07, but an ’06 alternator will match up precisely on the timing cover. Took me a long time to figure this out, since I had an ’07 alternator–I received 17V+ when wiring this up. Hope to save y’all some time.

    Reply
  2. Kevin Ashcraft

    I have o7 dodge Cummings gen3 can u put a extunal regalator on it and how i keep burning up alt

    Reply
  3. Thomas

    mine is a 1989 dodge ramcharger i did this to mine and it keeps eating regulators works fine for a month then starts over charging thoughts

    Reply
  4. Alan

    Hi Sir

    I seem to have this problem with my 2005 Sebring Convertible.

    It’s an intermittent problem – every time I think it’s fixed, I can drive the car for hours or days and it will suddenly go nuts again.

    I once had the alternator tested in the vehicle, WHILE it was acting up, and it failed saying “bad voltage regulator.” The parts guy sold me a new alternator – telling me the VR was in the Alternator. I replaced it – it worked fine for a couple of days then went nuts again.

    When I say “goes nuts” it basically bucks like a rodeo-bull every time you press the accelerator too hard. Back off, accelerate slowly and it will do OK, but will again “buck” out of nowhere while you’re driving along even at a steady speed…

    MIL light comes on, and It ALWAYS gives the same 4 codes – 2 have to do with low voltage, one is for (only one of) the Camshaft Position Sensor(s) and one for a bad Transmission Control Module – however the troubleshooting for the CPS and TCM errors BOTH say they can be caused by a low-voltage condition – which brings be back again to the voltage regulator…

    So… I think I need to do what you are suggesting here – I watched your vid then followed the link over to here – but I’m confused about one thing…

    When you say to connect the wire to the battery or the fuse-panel, how do you do that? Where would you connect the wire to the fuse panel to ensure it’s shut off when the key is turned off?

    Also, rather than run the wire to the battery or fuse-panel, could you just connect it to the charging post on the alternator itself? after all, it connects from there to the battery, right? or would that fry the whole deal due to the amount of current being put out by the alternator?

    Lastly, what if you simply put a diode in the wire so that the “juice” couldn’t flow backward from the battery to drain it? I’ve done this before in other applications…

    I’d REALLY appreciate your help – my email is @gmail.com…
    I’m stuck with no vehicle right now and live WAY out in the country so I *REALLY* need my car to be reliable!

    If you’d like to chat and you could call me at 8170, I’d be ETERNALLY grateful!

    Even if you choose not to respond, I’m thankful for the info you’ve already supplied!

    MOST sincerely,

    Alan

    Reply
    1. Bob

      If a external regulator is built and installed than is will slowly drain the battery when the key is off. This is the reason for breaking the connection to the positive side of the battery.

      Most wire the external regulator into the fuse box since the key will turn off power to the box. For example the radio fuse can be controlled with the key and will break a connection when the key is turned off.

      Sometime the fuse box is hard to get to so others install a switch and manually break the connection.

      Your idea about using a diode sounds like it might work. I have never tried it.

      Remember this is all a home built modification so if you have a better way to build one definitely do it.

      This is all about saving $400-$1000 dollars by building your own voltage regulator, so besides getting it working there really is no one way. The above is simply how I do it.

      It is possible for a bad voltage regulator to fry a alternator so you may want to test it again at a auto supply store.

      One last thing is that the voltage can also vary if the computer/ECM does not have a good ground to the case.

      On some cars I have looked at running a good ground wire to the alternator can solve this when they are not grounded good.

      If it doesn’t work with a good ground than I install a external voltage regulator.

      Good luck let me know what happens.

      Reply
  5. Neil J Snyder

    I did this because my voltage was over 17V. Now its 12.4V. Doesn’t it need to be 13.8-14.4V to charge the battery?

    Reply
  6. Kenny

    Hello, I just purchased a 2011 Durango. 3.6 liter. 180 amp alternator. is it possible to put an external voltage regulator to these later Style PCM controlled alternators? I see the kits available for the early Durangos but not for the later models. Seems my later style Durango has different wiring than the earlier models. Usually there are two field wires coming from the alternator along with the bigger battery wire. The wires going to my alternator are as follows: 1 thick wire going to battery, and two small wires – one is labeled field and the other is battery sense. So since my alternator obviously does not have 2 field wires how is this external regulator conversion possible?
    My year Durango has a alternator recall but unfortunately my VIN number does not fall under the recall. The recall is for the 160 amp alternators while I have a 180 amp. Alternator failed in a major way, internally shorting killing my battery and PCM with it. I was very lucky nothing caught fire.
    I have been searching and searching the web for a long time but can’t seem to find anyone with the later style Durangos or similar that has converted it to a external regulator.I’m thinking it’s not possible due to the fact it only has one field wire.if it is possible I would appreciate it very much if someone could help.
    One odd thing to mention is, since I know for a fact my alternator is not charging, I am getting no battery or alternator light. Alternator and battery have been replaced.even verified my new alternator is good by taking it to a local Alternator Rebuild shop to test. they said it was working fine.

    I would appreciate any help in getting me to converting my vehicle to an external regulator.

    Reply
    1. Ryan

      Did you ever figure this out? I have same model and issue. I did the bypass but now I’m getting 17 volts out of the alternator and the car simply does not like it at all!

      Reply
    2. Michael

      Did you ever figure this out? I have the same situation with a 2011 Durango and wondered if you tried this, and 9f so, was it successful? Thanks

      Reply
  7. Ray

    Followed direction perfect…. My 97 jeep Wrangler 4.0 5 speed seemed to have a failing pcu, only because the voltage regulator is controlled by the pcu. I could not locate the proper pcu swap and as I was under a time crunch I opted to give the external regulator swap a go…. It has all gone flawless except… The battery/voltage Gage on the dash pegs out under load. I dropped down to a 10amp inline fuse to see if it would blow…it hasn’t. Any thoughts?

    Reply
    1. Nick martin

      I’m having same exact thing happen how did you resolve your problem

      Reply
  8. Bryan

    I have a 03 dodge Dakota and I put a 1990 voltage regulator on it. I am get an over charge it’s putting out about 16 volts when I get the Rpms over 2000. I’ve checked my gound wire and I even added a ground wire to the battery terminal. What should I do.

    Reply
  9. Ashley Brogden

    Will this work if the ecm. Is completely fried?

    Reply
    1. Robert

      Hi

      I have a red lighton my dashboard could I use this voltage regulator on my 2008 chrysler300 c instead of buying another alternator wire this instead

      Look forward to hearing from you soon
      Robert

      Reply
  10. Richard

    Ok, so I hooked up a voltage regulator everything was properly grounded and connected. But my issue is the wire from the battery to the toggle switch for on/off melted off the protection on the wire. I don’t know if I should go bigger or maybe I should have had a fuse inbetween these 2. either way I need some major assistance. I don’t know what had happened or how it happened but I do know that the regulator was running at 15. maybe .50 more but no less everything worked right just that wire fried quickly for the switch. just the one from the battery to the switch.

    Reply
    1. Bob

      I always use a fuse just in case something like that happens. The gauge may need to be thicker or the switch is grounding out somewhere. Let us know what you find.

      Reply
  11. Terry Fulk

    TERRY,
    Hello there, I’m having a hard time with the charging system for my 1975 Dodge D-100 custom 225 SLANT 6. I’ve replaced the Alternator 65 AMP. & THE VOLTAGE REGULATOR & THE ELECTRONIC MODULATOR – LOTS OF PEOPLE WILL CALL IT AS THE BRAIN BOX. SO I’M RUNNING THE ENGINE & LATER I NOTICED THAT THE LIGHTS IN THE CAB IS GETTING VERY DIM – THEN IN A BIT THE ENGINE SHUTS OFF AND I HAVE A DEAD BATTERY. SO IF YOU HAVE ANY INFORMATION TO GIVE ME I APPRECIATE IT. SO PLEASE ????? LET ME KNOW ANY INFORMATION???????
    THANK YOU. 😁

    Reply
    1. ChikNChuker

      terry you should do a voltage drop test on your battery cables. this test is obviously better if you put a load on the battery and cable system but can be done without a load too. just check with volt meter to see voltages from one point to the next. i believe you may just have excessively corroded cables where you cant see it unless you pull insulation off the whole cable. which you shouldnt do unless you replace the whole cable. good luck.

      Reply
  12. Daniel Taylor

    Hey great idea! THE PROBLEM WITH THIS IS CALLED DIODE DRAIN BACK. ALL ALTERNATORS MAKE 3 PHASE CURRENT. When a diode goes bad (inside a regulator or a PCM) they drain voltage from the battery backwards to ground. ALL CARS REQUIRE RECTIFICATION OF 3 PHASE CURRENT TO 12vdc. So the all have to use something like a diode to rectify the current. So if you bypass the PCM with a faulty rectifier and do not remove it from the system–IT WILL STILL DRAIN VOLTAGE.

    Reply
    1. Gary Beharrell

      Daniel.
      The regulator controls the field current. The rectifier is in the alternator, not the pcm. You are correct that all vehicles with alternators rectify the stator output with diodes but that is completely separate from the field or regulator circuit. You are correct in that if the rectifier(in the alternator) is defective it could drain the battery, but you are incorrect saying the PCM regulator will drain the battery as in this case the PCM grounds the field of the alternator. So to drain the battery it would have to have a stuck on field supply relay and a shorted to ground circuit in the PCM. Go ahead and wire the external reg. if you want. You may have a check light on and your voltmeter may not read but it will charge fine and not drain the battery if installed properly

      Reply
  13. Craig Milliman

    Bob, I’ve tried your fix, wiring the external regulator in the way you suggest. Symptoms on my 2000 Dodge RAM 3500 van were–and still are–the following:

    On engine start, the check gauges light comes on, the fuel gauge snaps all the way to the right (full) position, and the oil pressure gauge also snaps full right. The ammeter goes all the way to the left.
    After driving for a while, something happens. Oil pressure and ammeter return to normal. Fuel gauge stays at full. Check gauge light goes out.
    In connecting the new regulator, I used the old two-wire plug on the back of the alternator by cutting the wires and splicing in new wires. The old wires are thin, maybe 16 or 18 gauge. I used 14 gauge. Would mixing wires cause a problem?
    Not sure if I have a good ground. Couldn’t find a good place to connect the ground to the alternator, so I’m relying on the screws securing the new regulator to the sheet metal for a ground. Should this work?
    The one change I have noticed is that when driving and the oil pressure gauge returns to normal, the fuel gauge stays at full and the ammeter swings all the way to the right, indicating the alternator is charging at nearly 18 volts. Hmmm.
    Should I rewire the connector with all 14 gauge wire? Should I use thinner wire throughout? Should I try to improve the ground?
    Thanks for all the help you have already given us.
    Craig

    Reply
    1. Tomt

      Using an external voltage regulator separates the charging system from the vehicle. It should not be effecting any dashboard lights except charging. Check with a volt meter it is not over charging and maintaining the voltage correctly, that is all it does.

      Reply
      1. Craig Milliman

        Well, I managed to get a good ground to the alternator and everything worked.
        Now I have a slightly different problem. Bob said to wire the regulator through the fusebox so the regulator wouldn’t draw down the battery. I didn’t know how to do that, so I thought I could just unplug the wiring pigtail from the regulator. Now I have a very dead battery and the ammeter shows the battery not being charged when I jump start the engine.
        I guess unplugging the regulator didn’t get the job done?

        Reply
  14. Lucas Phillips

    So I did the external regulator on my 2005 Dodge Magnum. It seems to be working. But my battery lite is staying on all the time. Is this because of bypassing the internal regulator?

    Reply
    1. Douglas

      Battery Light will stay on because you bypassed the regulator in the brain causing it to throw a fault i.e. the battery light

      Reply
  15. Douglas randolph Newsom

    hi,
    i did the external regulator. I used a regulator from a dodge( brand new from autozone) and the factory oem plug.
    i cut the wires coming out of the alternator and wired in the regulator. all the wires were the same color due to oem. blue to blue and green to green. The top wire going into the regulator is blue i added a switched power source, directly from the battery to switch to regulator. it does not charge still. the battery and alternator are both new and tested. thnking it may be the switch i took it out and just twisted them together. still no charge. Any help would be appreciated

    Reply
    1. Gary Beharrell

      Douglas.
      Make sure you have a good ground on the regulator.
      Hope you hooked them to the alternator side of the wires you cut.
      cheers.

      Reply
  16. Erik

    The external regulator fix is great, but the CEL won’t go off because the ECM is still looking for a load across the two wires that were removed from the back of the alternator, the field wires. While there is a kit that includes a resistor to solve this problem, if someone might have access to what that load was , it would be much cheaper to get a resistor at an electronics supply rather than spend more (double of triple) just because it is from a kit.

    Reply
  17. Bob

    The regulator in my PCM is still good, what would happen if I just tapped in on the 2 regulator wires coming from the PCM and left them hooked up to the PCM also, along with installing the new external regular?

    Reply
  18. Bill

    My alternator wouldn’t charge unless I revved the engine up and then after a few minutes it would quit. I thought it had to be the voltage regulator. I bought an external one and couldn’t get it to work for anything no matter how I hooked it up. I got pissed and sprayed choke cleaner on the alternator (let it dry) and it started working. When I had it checked it happened to be charging. So if you haven’t spent the money yet try that

    Reply
  19. dstaylor188

    If the diodes in the PCM are bad do they cause a drain back like diodes in a bad alternator?

    Reply
  20. Ron C

    We just installed an external voltage regulator on a 1999 Jeep Wrangler after verifying the issue was the PCM voltage regulator. The 12 V wire to the alternator (green with orange stripe) was tapped to supply voltage to the external voltage regulator and the alternator field supply. Power to this wire is switches on and off with the ignition switch, so that issue disappears. The alternator field return wire (green to the PCM) was cut and wired to the field connection on the external voltage regulator. To prevent an MIL light, a 10 ohm resistor is connected from the 12V alternator supply wire (green with orange strip) to the cut green wire back to the PCM. Since the PCM voltage regulator output doesn’t switch to ground properly (PCM connector C2, pin 10), the wattage of the resistor doesn’t matter. A 1/4 watt resistor works fine and doesn’t get hot because the PCM output is broken. (If the PCM works, a 1/4 watt resistor is too small, will get very hot and fail quickly.) The purpose of the resistor is to supply voltage back to the PCM to trick it into thinking the alternator field coil is still connected.

    Our installation works great and took about an hour to install. The voltage regulator was purchased at Advanced Auto. It is for a 1980 Dodge Ramcharger with 5.9L 360CI V8 Carb. We used Carquest BWD Voltage Regulator , Part # R296P ($20) with connector Part # PT173 ($11). Our alternator’s max field current is around 4 amps, so 16 or 18 AWG stranded wire works fine. It is important the voltage regulator case is well grounded to the car chassis, not necessarily to the alternator case. The external voltage regulator case connection supplies a return path back to the battery, not to the alternator. A continuity check from the battery negative terminal to the external voltage regulator case tells the story. The lower the ohms, the better the connection.

    Good Luck!

    Reply
    1. Joel

      Ron –
      Would you be able to draw a quick schematic for what you did?
      Thanks

      Reply
  21. Daniel

    I have the perfect solution. Go buy something from the 1980’s that is fuel injected ( I bought an 85 Ford Ranger and a 1990 Ram). You can still get most of the parts and they’re easy to fix and reliable too. And, since it’s over 30 years in some states you can get Antique Plates. You never have to buy tabs or emission check it ever again.

    I’ve got one thing to say for all you senceless tree huggers who destroy people’s lives with their environmental BS, F- U!

    Reply
  22. tom

    I tied into the thick alternator to battery wire with the middle external voltage regular (red) wire and just connected a wire to one of the terminals on the back of the alternator .check eng light stays on but it works.will something fry ? Let me know what you think.

    Reply
  23. Marcus

    Nice write up! The only thing I might add regarding the 15V over-voltage issue is to make sure the ‘red’ switched circuit has adequate connectivity to the battery – it functions both as a current supply for the field circuit and, more importantly, a sense wire for the external regulator. As you may know, if the key switched circuit is not able to supply sufficient current to the field winding (due to high resistance in fuse box or poor connectivity to positive battery voltage), it will cause a drop in voltage on the regulator sense circuit as well (because they are both on the same wire in this installation). This in turn causes the regulator field current to try to increase further to generate more voltage at the ‘output post’ to compensate for the low voltage sensed by the regulator. The end result is the battery will be over charged and boil off the electrolyte (not good!) and potentially could fry your electronics.
    My 2c worth would be to insert a relay that is triggered by the keyed circuit in the fusebox, and run the red circuit directly (via the relay for on/off) to the battery. This provides up to 25/30Amps of independant low resistance 12V power directly to the voltage regulator ensuring that there isn’t any parasitic losses on the sense circuit. It also ensures that the battery is receiving full voltage (in the event of any dodgy ground or power circuit connections) at the terminals to maintain a healthy state of charge.

    Reply
    1. whattaguy

      Electrician here for 40 yrs. I did this mod to my 97 Jeep when it was consistently undercharging. What I found was that Marcus is the one guy that is right about the 15 volt issue and his suggestion will fix it.
      The ASD relay feeds the ASD input on the PCM, which then drives the Gen field SOURCE 12v and the Gen field driver. What I found was my initial startup was charging at 14.8 ish with a good digital meter. Too high. So I checked for a voltage drop to the Gen Source, and there it was, a drop of .25 volts. So the regulator being driven by the field source is going to be that much low and it will try to bump up the field current to get it to around 14.5 , which it may never get to because the PCM is where the voltage is getting lost. The whole idea of the external regulator in the first place is usually to take the defective regulator in the PCM out of the picture anyhow so it makes sense to do just that by using the field source from the PCM to switch a relay from the battery to the + connection on the regulator.
      Doing so will let the regulator see what the battery itself is seeing in terms of voltage.
      This also makes you wonder what else might be wrong in the pcm if it can’t source BAT voltage..
      or maybe the ASD relay is dirty
      there is my 4 cents

      Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.